Fanuc Tp Editor Software

Posted on 17-08-2021 by admin

For safe use of FANUC robots, you must read and follow the instructions in “FANUC Robot SAFETY HANDBOOK (B-80687EN)”. 1 DEFINITION OF USER The personnel can be classified as follows. Operator:. Turns the robot controller power on/off. Starts the robot program from operator panel Programmer or Teaching operator:. Operates the robot.

PaintPRO software is a graphical offline programming solution that simplifies robotic path teach and paint process development. PaintPRO is specifically designed to create paths that can be utilized by FANUC America Corporation's PaintTool™ application software. Request Product Description Page.
FANUC’s TP programming language and the teach pendant’s built-in editor are great tools. They allow relatively novice programmers to get up and running very quickly. Teach a couple points, throw in a couple labels and IF statements, and you’re off to the races. However, anyone who’s tried to do anything a bit more complex quickly realizes how cumbersome programming on the teach pendant is.
Get all of Hollywood.com's best Movies lists, news, and more.

Ah, the old backup game. What could be more fun than taking backups for a dozen, a hundred, or a thousand robots? If you’re reading this, you probably know that there is something that’s a lot less fun than managing backups: not having a backup when you need one. Reprogramming a production robot from scratch – now that sounds like a pain. In this post, we’ll look at how to backup and restore a Fanuc R-30iB controller.

Contents of this post:

Types Of Fanuc Backups
MD Backup and Restore Process on Fanuc R-30iB
IMG Backup and Restore Process on Fanuc R-30iB

Types Of Fanuc Backups

Like many electronic controllers, the Fanuc R-30iB offers more than one possible backup method. The two common Fanuc backup solutions are referred to as “MD backups” and “image backups” (or “IMG backups”).

Fanuc MD Backups

MD backups preserve the “user-editable” portions of the controller. To be specific, MD backups record the contents of SRAM, which consists of the following:

Teach Pendant programs
Frames
Variables
Mastering
Menu settings
I/O configuration
and more

MD backups are not a complete controller backup.If you lose a main board or FROM/SRAM module, or otherwise have to completely reload your robot controller, an MD backup will not get you up and running by itself.

With that said, it would certainly be better than nothing. If you had a similar robot nearby, you could backup and restore an image from that robot. After doing so, you could restore your MD backup on top of the image. You would have a lot of work to do before you’d be out of the woods, and would be reteaching a lot of positions, but at least you’d have all of your programs.

When would you use a Fanuc MD backup?

While MD backups won’t fully restore a controller, they do have their distinct uses. I would say MD backups are most useful for two purposes:

Development and debug
Quickly restoring a single (or a few) teach pendant program(s)

In the shop where I work, a common use for MD backups is as reference material for debug and development. Robot programs that are stored in your MD backups can be viewed in a text editor, if you’ve saved your ASCII programs, or converted to readable forms with Fanuc utilities. If you’ve consolidated your backups onto one computer, you can use them to compare logic from similar applications or to borrow logic for new robot programs.

Additionally, MD backups can come in handy big-time if you have to revert to an earlier robot program.

For instance, let’s say the integrator on the previous shift moves a position to try to improve cycle time. During your shift, you find that the new position causes a portion of the robot dress to contact the part. If you have a copy of the MD backup on a thumb drive (or in PC File Services), you can quickly load your backed up version of just that one program.

Fanuc IMG Backups

An image backup is a complete image of the robot controller’s contents – both FROM and SRAM. If you have an image, you can fully restore the robot in the event of FROM/SRAM module or main board failure. An image stores everything that an MD backup stores, plus the robot’s core software, patches, and any software customizations that have been loaded for your facility.

Image backups are obviously the more complete backup solution. There’s no doubt about it – it is an absolute necessity to maintain an image backup for each and every robot, especially for production robots.

With that said, IMG backups do have one major drawback. Their contents are not easily read. As a result, they don’t offer the same value in reference and simplicity that’s found with MD backups. Images are all or nothing – their only use is to completely restore the controller.

A Final Thought On Fanuc Backup Types

You have to have images. There’s no getting around it unless you want to be teaching every point and doing a ton of config whenever you lose a main board or controller.

If you’re already visiting every robot in your facility to take image backups, it’s only a few more minutes per controller to take MD’s as well. You might as well perform both backup processes at each robot. You’ll get the images you need, plus the MD’s, which might just come in handy for development, debug, and partial restorations.

MD Backup and Restore Process on Fanuc R-30iB

How To Perform a Fanuc MD Backup

Obtain a thumb drive with plenty of room available:
- A typical MD backup is around 10 MB, depending on your robot programs and other content
Insert the thumb drive into either the USB port in the black door on the controller (UD1:) or the USB port on the right side of the teach pendant (UT1:)
On the TP, press the MENU button then select File -> File
On the FILE menu, press F5 [UTIL]. If [UTIL] is not shown above F5, press NEXT until [UTIL] is shown and then press F5
Select Set Device
Select either USB Disk (UD1:) or USB on TP (UT1:), depending on where you inserted your thumb drive
Press F5 [UTIL] again and select Make DIR
Enter a new directory name that will help you remember which robot you’ve backed up. I like to use the Upper Case input method (like my old Nokia flip phone)
Once you have made your new directory, you should be taken there. The directory listed on the top line should be UT1: (or UD1:) {YOUR-NEW-DIR}*.*
Press F4 [BACKUP]
Select All of above
You will be prompted to “Delete UT1: (or UD1:) {YOUR-NEW-DIR} and backup all files?”. Press F4 YES
The MD backup will commence. Typical backup time is ~2-3 minutes, depending on the contents of your robot

Backing Up ASCII Programs

If you would like to save the ASCII (human-readable) versions of the robot programs as well, then, without leaving your thumb drive directory in the FILE menu:

Press F4 [BACKUP]
Select ASCII programs
You will be prompted to “Save UT1: (or UD1:) {YOUR-NEW-DIR}{PROGRAM-NAME}.LS?”. Press F3 ALL
The ASCII program backup will commence. Typical backup time is ~2 minutes, depending on the contents of your robot programs

How To Restore From a Fanuc MD Backup

Obtain a thumb drive with a previous MD backup for the robot you’re working on
Insert the thumb drive into either the USB port in the black door on the controller (UD1:) or the USB port on the right side of the teach pendant (UT1:)
Perform a Controlled Start:
1. Cycle power to the controller
2. As soon as the robot starts to power back up, hold PREV and NEXT on the teach pendant to be taken to the Configuration Menu
3. Type 3 and press ENTER to initiate a Controlled Start
Once the teach pendant boots back up, press the MENU button then select File -> File
On the FILE menu, press F5 [UTIL]. If [UTIL] is not shown above F5, press NEXT until [UTIL] is shown and then press F5
Select Set Device
Select either USB Disk (UD1:) or USB on TP (UT1:), depending on where you inserted your thumb drive
Navigate to the directory in which your MD backup is stored. If no files or directories are shown, you will have to press ENTER on (* * (all files)) to see the thumb drive’s contents
If [RESTOR] is not shown above F4, press FCTN, then select RESTORE/BACKUP to toggle between restore and backup
Press F4 [RESTOR]
Select the type of restore action that you want:
1. System files (system variables, servo parameter data, and mastering data)
2. TP programs (.TP, .DF, and .MN files)
3. Application (“Non-program application files”. If you know what this means, let me know in the comments.)
4. Applic.-TP (All of the above, except system files)
5. Vision data
6. All of above
You will be prompted with “Restore from UT1: (or UD1:) (OVERWRT)?”. Press F4 YES
The TP will show “Accessing device. PREV to exit.” for about 30-60 seconds, then the restore will commence. Once it begins, typical restore time is ~2-6 minutes, depending on the contents of your robot
As many files as possible will be restored. Once the restore is complete, you will need to perform a Cold Start:
1. Press FCTN
2. Select START (COLD)

Restoring a Single Robot Program From a Fanuc MD Backup

Make sure that the file you want to restore is not currently being edited
Obtain a thumb drive with a previous MD backup for the robot you’re working on
Insert the thumb drive into either the USB port in the black door on the controller (UD1:) or the USB port on the right side of the teach pendant (UT1:)
On the TP, press the MENU button then select File -> File
On the FILE menu, press F5 [UTIL]. If [UTIL] is not shown above F5, press NEXT until [UTIL] is shown and then press F5
Select Set Device
Select either USB Disk (UD1:) or USB on TP (UT1:), depending on where you inserted your thumb drive
Navigate to the directory in which your MD backup is stored. If no files or directories are shown, you will have to press ENTER on (* * (all files)) to see the thumb drive’s contents.
Find the {PROGRAM-NAME}.TP program that you would like to restore. Scroll down so that the name of that program is highlighted.
With the program name highlighted, press F3 LOAD
Press F4 YES
If it’s an existing program, you will be prompted with “UT1: (or UD1:) {YOUR-BACKUP-DIR}{PROGRAM-NAME}.TP already exists”. Press F3 OVERWRITE
The restore will commence. Once it does, it should only take a few seconds, and you should see “Loaded UT1: (or UD1:) {YOUR-BACKUP-DIR}{PROGRAM-NAME}.TP” when the restore is complete.

IMG Backup and Restore Process on Fanuc R-30iB